TEST OPERATION
WIRING DIAGRAM
Disassemble procedure
Unscrew 2 screws on the back of the
top plate.
Pull the top plate backward and upward as shown.
Pull out the drawer and unscrew 2
screws.
Lift the side the Control Panel Assembly and pull it out
Push out PANEL ASSEMBLY,CONTROL after
Push the hook below
Unscrew the 10 screws from the Control
Panel Assembly.
Disassemble the Display PWB Assembly.
Disconnect connector from the wiring.
Two screws are unscrewed.
Push the hook of between BASE,CABINET
and PWB ASSEMBLY below as shown.
Pull the PWB assembly (Main) to arrow direction.
Inlet valve removal
Disassemble the top plate assembly.
Pull out the drawer.
Push out the DISPENSER ASSEMBLY after unscrew 2 screws.
Unscrew the nut at the lower part of
the dispenser.
Disassemble the 3 or 4 connectors from
the valves.
① Red Housing(BK/WH-YL/BK)
② NA Housing(WH/BL-BK)
③ Blue Housing(GY/WH-BK)
④ Red Housing(BL/RD-BK)
Unscrew 2 or 4 screws from the back of
the cabinet.
Unscrew 2 or 4 screws from the back of
the cabinet.
Cabinet cover removal
Unscrew the 2 screws from the lower of
the DECO PANEL.
Unscrew the 4 screws from the back of
the DECO PANEL
Pull out the DECO PANEL
Unscrew the 4 screws from upper of the
cabinet cover.
Unscrew the screw from filter cover.
Put a flat ( - ) screwdriver or putty
knife into the both sides of the filter cover, and pull it out.
Unscrew the screw from the lower side
of the cabinet cover.
Open the door.
Disassemble the clamp assembly.
Tilt the cabinet cover.
Disconnect the door switch connector.
NOTE: When assembling the CABINET
COVER, connect the connector.
Lift and separate the cabinet cover.
Disassemble the clamp assembly.
Disassemble the Gasket.
Open the door.
Remove the two screws from the Hinge.
When removing the Door Assembly, it is necessary to hold the break is inner of
the cabinet cover.
[Be careful: The door is heavy.]
Open the door and disassemble the
CLAMP ASSEMBLY.
Unscrew the 2 screws.
NOTE: Reconnect the connector after
replacing the DOOR SWITCH ASSEMBLY.
Disassemble the cabinet
cover
Separate the pump hose, the bellows
and the circulation hose assembly from the pump assembly.
Disassemble the pump assembly in arrow direction.
Separate the pump hose, the bellows
and the circulation hose assembly from the pump assembly.
Disassemble the pump assembly in arrow direction.
CAUTION
• When assembling the heater, insert the heater into the heater clip on the
bottom of the tub and check the position of wire color.
• Tighten the fastening nut so the heater is secure.
Disassemble the cabinet cover.
Unplug the white connector from the thermistor.
Pull it out by holding the bracket of the thermistor.
When foreign object is stuck between drum and tub
Disassemble the cabinet cover.
Separate the heater from the tub.
Remove any foreign objects (wire, coin, etc.) by inserting a long bar in the
opening.
Disassemble the back cover.
Remove the bolt.
Pull out the Rotor.
Unscrew the 2 screws from the tub
bracket.
Remove the 6 bolts on the stator.
Unplug the 2 connectors from the stator.
Disassemble the damper hinges from the
tub and base.
Separate the dampers.
NOTE:
Once removed, replace the damper with new one.
To check out the fault diagnosis of
TSG, in case of removing the water inside, you can pull out the plug and let
the water drain away.
Be cautious in case of the TSG is hot
temperature.
Remove the housing coupled the TSG
(Heater, Water level frequency-sensor, Thermistor)
Taking out the screw of the TSG and
Body Frame.
Taking out the screws of Body Frame
(2EA)
Separate the hoses from the TSG.
Remove the Body Frame and then,
separate the TSG from the washer.
Exploded view
