Toshiba MC753DVD software update, SMPS circuit diagram

Firmware Update
Save the firmware update file to an empty media (CD-R / RW or 'Memory key'). The name of File must necessarily be dvdrom.bin

With the display indicating 'NO DISC ', insert the CD /'Memory key' with the update firmware. The screen will appear.

Using the remote control navigation keys, select:
<O>: to proceed with the update or
<X>: to cancel it.
Press ENTER (or wait for the countdown to start updating automatically)
The screen below will appear. Do not turn off the power at this stage.
Once the update is complete, the device will shut down. Remove the CD /'Memory key '.
When you reconnect it, the DVD door opens automatically.
Verifying the Firmware Version
To check the version of firmware in use, press 10> 7> 2> 9> ENTER in the sequence. [SERVICE MODE]
The screen below will appear and the version of the installed firmware can be verified.
In the example below, the version is [5CA1139C]

SMPS schematic

Panasonic Digital cameras – Panasonic Lumix DMC-FZ28 – Error code Display – Lithium Battery replacement – Initialization

A. The temporary cancellation of initial setting:
Set the REC/PLAY switch to “[Recording]”.
Set the mode dial to “[ P ]”.
While keep pressing [ AF macro/Focus switch ] and “[ UP ] of Cursor button” simultaneously, turn the Power on.
B. The display of error code:
Press [ AF macro/Focus switch ], [MENU] and “[ LEFT ] of Cursor button” simultaneously with the step 1 condition.
The display is changed as shown below when the above buttons is pressed simultaneously.
Normal display > Error code display > Operation history display > Normal display > .....

C. The change of display:
The error code can be memorized 16 error codes in sequence, however it is displayed 5 errors on the LCD.
Display can be changed by the following procedure:
“[ UP ] or [ DOWN ] of Cursor button” : It can be scroll up or down one.
“[ LEFT ] or [ RIGHT ] of Cursor button” : It can be display last 5 error or another 5 error.
D. How to read the error date:
The error date code is displayed from the left in order at the year, month, day, time.
Error date information is acquired from “Clock setting” information when the error occurs.
When the clock in not setting, it is displayed as “00000000”.

E. How to read the error code:
One error code is displayed for 8 bit, the contents of error codes is indicated.

How to Replace the Lithium Battery
Replacement Procedure
1. Remove the Main PCB.
2. Remove the Lithium battery and then replace it into new one.

How to Discharge the Capacitor on Main PCB

1. Put the insulation tube onto the lead part of Resistor (1kOhm /5W).
2. Put the resistor between both terminals of capacitor on MAIN PCB for approx. 5 seconds.
3. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.

INITIAL SETTINGS

PROCEDURES:
Step 1. The temporary cancellation of initial setting:
Set the REC/PLAY switch to “[ Recording ]”.
Set the mode dial to “[ P ]”.
While keep pressing [ AF macro/Focus button ] and “[ UP ] of Cursor button” simultaneously, turn the Power on.
Step 2. The cancellation of initial setting:
Set the REC/PLAY switch to “[ Playback ]”.
Press [ AF macro/Focus switch ] and “[ UP ] of Cursor button” simultaneously, turn the Power off.
Step 3. Turn the Power on:
Set the REC/PLAY switch to “[Recording]”, turn the Power on.

Step 4. Display the INITIAL SETTING:
While keep pressing [ MENU ] and “[ RIGHT ] of Cursor button” simultaneously, turn the Power off.

There are two kinds of “INITIAL SETTINGS” menu format.
[ 1. After replacing MAIN P.C.B./FLASH ROM ]

[ 2. Other than “After replacing MAIN P.C.B./FLASH ROM” ]

Step 5. Set the INITIAL SETTING

The model suffix can be chosen JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.
Select the area carefully.
Select the area with pressing “[ UP ]/[ DOWN ] of Cursor button”, and then press the “[ RIGHT ] of Cursor button”.

The only set area is displayed, and then press the “[ RIGHT ] of Cursor button” after confirmation.
(The unit is powered off automatically.)
Confirm the display of “PLEASE SET THE CLOCK” in English when the unit is turned on again.
Step 6. CONFIRMATION:
The display shows “PLEASE SET THE CLOCK” when turn the Power on again.
When the unit is connected to PC with USB cable, it is detected as removable media.

Service Mode - Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.
2. How to display
The error code can be displayed by the following procedure:
Before perform the error code memory function, connect the AC adaptor or insert the battery.
(Since this unit has built-in memory, this error code memory function can be performed without inserting SD memory card.)

DIRECTV Universal Remote Control code list for DLP TV - Plasma TV - How to program the remote

DIRECT CODE entry SETUP
1. Turn on the TV.
NOTE: Please read steps 2-5 completely before proceeding. Highlight or write down the codes and component you wish to set up before moving on to step 2.
2. Locate the code for your TV.
3. Slide the MODE switch to the TV position.
4. Press and hold the MUTE and SELECT keys at the same time until the green light under the TV position flashes twice, then release both keys.
5. Using the number keys enter the 5-digit code for your brand of TV. If performed correctly, the green light under TV flashed twice.
6. Aim the remote at your TV and press the PWR key once. Your TV should turn off. If it does not turn off, repeat steps 3 and 4, trying each code for your brand until you find the correct code.
7. Slide the MODE switch to the DIRECTV position. Press TV POWER. Your TV should turn on.
CODE SEARCH
1. Slide the MODE switch to the appropriate position.
2. Press and hold the MUTE and SELECT keys at the same time until the green light under the selected switch position flashes twice, then release both keys.
3. Enter 9-9-0. (The green light under the selected switch position flashes twice.)
4. To view the first digit in the code, Press and release the number 1 key. Wait three seconds, and count the number of times the green light flashes. Write this number.
5. Repeat step 4 four more times for the remaining digits; i.e., press number 2 for the second digit, 3 for the third digit, 4 for the fourth digit and 5 for the final digit.
Setup Codes for DLP TV
Hewlett Packard 11494
HP 11494
LG 11265
Magnavox 11525
Mitsubishi 11250
Optoma 10887
Panasonic 11291
RCA 11447
Samsung 10812, 11060, 11312
SVA 10872
Toshiba 11265, 11306
Vizio 11499
Setup Codes for PLASMA TV
Akai 10812, 11207, 11675, 11688,11690
Albatron 10843
BenQ 11032
Byd:sign 11311
Daewoo 10451, 10661
Dell 11264
Delta 11369
Electrograph 11623, 11755
ESA 10812
Fujitsu 10186, 10683, 10809, 10853
Funai 11271
Gateway 11001, 11002, 11003, 11004,11755, 11756
H & B 11366
Helios 10865
Hewlett Packard 11089, 11502
Hitachi 10797
HP 11089, 11502
iLo 11684
Insignia 11564
JVC 10731
LG 10178, 10056, 10829, 10856, 11423, 11758
Marantz 10704, 11398
Maxent 11755, 11757
Mitsubishi 10836
Monivision 10843
Motorola 10835
Moxell 10835
Nakamichi 11493
NEC 11398, 11704
NetTV 11755
Norcent 10824, 11089, 11590
Norwood Micro 11303
Panasonic 10250, 10650, 11480
Philips 10690
Pioneer 10679, 11260, 11398
Polaroid 10865, 11276, 11327, 11328
Proview 10835
Runco 11398, 11679
Sampo 11755
Samsung 10812, 11312
Sharp 10093
Sony 10000, 10810, 11317
Studio Experience 10843
SVA 10865
Sylvania 11271, 11394
Tatung 11101, 11285, 11287, 11288, 11756
Toshiba 10650, 11704
US Logic 11303
Viewsonic 10797, 11755
Viore 11207
Vizio 11756, 11758
Yamaha 10797
Zenith 10178

Panasonic High Definition Video Camera - Panasonic HC-V700EB – Service mode – Service mode setting

Service Mode
1. Indication method of the service menu
Set the mode switch “Motion Picture Recording” mode.
2. While the power is turned OFF, keep pressing the “Power” button, “Zoom lever” to W side and “intelligent auto/Manual” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed.

3. End method of the top screen of the service mode menu
Touch the [ EXIT ] of LCD to end the service mode, and then POWER OFF.

Built-in Memory Self Check Execution (HC-V700M/V707M only)
Touch the [ 3 ] of LCD, select Built-in memory self check execution.

Indication contents

Built-in memory self check result display
Display the Built-in memory self check execution.
Displays other than “OK” are abnormalities of Built-in memory.
Touch the [ BACK ] of LCD to end the service mode, and then POWER OFF.
Lock Search History Indication
Touch the [ 4 ] of LCD, select Lock search history indication.

Indication contents

Lock search history indication
Display the camera system error cord for three histories saved in EEPROM.
The error cord contents which are displayed

Touch the [ BACK ] of LCD to end the service mode, and then POWER OFF.

Power ON Self Check Result Display
Touch the [ 5 ] of LCD, select Power ON self check result display.

Indication contents
Power ON self check result display
Function to diagnose correct function of the device and interface between devices result display.
Display the following communication test result.
- CAM-PWR : communication test between IC3401 and IC1503
- CAM-UNI : Internal communication test of IC3401
Display other than “OK” are abnomalities of each lines.
Cutting of battery connection or AC power supply connection to end the service mode.
Forced full flash emission
Touch the [ 9 ] of LCD, select Forced full flash execution.
Indication contents
Discharging the capacitor without using register.
Forced full flash emission for charge capacitor completely discharge.
To prevent electric shock, we recommend enforcement before disassembling.
Cutting of battery connection or AC power supply connection to end the service mode.

Erasing the lock histories
Touch the [ 10 ] of LCD, select erasing the lock histories execution

Indication contents

Erasing the error histories stored in EEPROM. (working time is not erased)
Cutting of battery connection or AC power supply connection to end the service mode.
Camera data indications while the video playback
Touch the [ 12 ] of LCD, select indicating the camera informations while playing back the recorded video.
Indication contents
While playing back the recorded videos, the camera informations (Shutter speed, Iris value, White balance and focal length) are superimposed on the LCD screen.

Sony 7.1 channel HD AV Receiver - Sony STR-DA5300ES – How to clear the memory – Special menu mode – How to adjust the IDLE current

FLUORESCENT INDICATOR TUBE PATTERN CHECK MODE 
When this test is activated, all segments turn on at the same time, then each segment turns on one after another.
Procedure:
1. While pressing the [MOVIE] and [DMPORT] buttons, press the [POWER] button to turn on the main power.
2. All segments and all LEDs turn on.
SOUND FIELD CLEAR MODE
The preset sound field is cleared when this mode is activated.
Procedure:
1. While pressing the [MUSIC] button, press the [POWER] button to turn on the main power.
2. The message “S. F. Initialize” appears and initialization is performed.
MEMORY CLEARING MODE
All preset contents are cleared when this mode is activated.
Procedure:
1. While pressing the [TONE MODE] and [DMPORT] buttons, press the [POWER] button to turn on the main power.
2. The message “MEMORY CLEARING***” appears and the memories are reset to the default values.
3. When done, the message “MEMORY CLEARED*” appears.
TUNER AM STEP CHANGE (9 kHz/10 kHz) MODE
Either the 9 kHz step or 10 kHz step can be selected for the AM channel step.
Procedure:
1. Press the [POWER] button to turn on the main power.
2. Turn the [INPUT SELECTOR] dial to select the “AM”.
3. Press the [POWER] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the [POWER] button to turn on the main power.
5. Either the message “AM 9kHz Step” or “AM 10kHz Step” appears, select the desired step.
COMMAND MODE CHANGE MODE
The command mode of the remote-commander which this set receives can be changed.
Procedure:
1. While pressing the [2CH/A. DIRECT] button, press the [POWER] button to turn on the main power.
2. Either the message “COMMAND MODE [AV1]” or “COMMAND MODE [AV2]” appears. Select the desired mode.
SF LOCK ON/OFF CHANGE MODE
Procedure:
1. While pressing the [MUSIC] and [DMPORT] buttons, press the [POWER] button to turn on the main power.
2. Either the message “SF LOCK [OFF]” or “SF LOCK [ON]” appears.
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in order, the message “MENU SPECIALIZED!” appears.
2. Press the  UP/DOWN button of the remote commander, the message “<<< SPECIAL >>>” appears.
3. Press the RIGHT button of the remote commander, the item is appears.
4. Each time the UP/DOWN button of the remote commander is pressed, the item is switched to another.
Some items can change the content. Display the cursor by pressing the RIGHT button of the remote commander, and changing the content by pressing the UP/DOWN button of the remote commander, and fix the content by pressing the LEFT button of the remote commander when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in order again, the message “MENU SPECIALIZED OFF” appears.
BIAS ALIGNMENT ADJUSTMENT
Note: Power up the amplifier and leave for 10 minutes to warm up. Then adjust the Idle current each channels .
Connection:
CN1561 (CN1611, CN1761, CN1861) pin 1, CN1561 (CN1761, CN1861) pin 3  TO THE POSITVE PROB OF VOLTMETER
CN1561 (CN1611, CN1761, CN1861) pin 2, CN1561 (CN1761, CN1861) pin 4 TO THE NEGATIVE  PROB OF VOLTMETER
Note: Pin 3, 4 of CN1611 are open.
Procedure:
1. Connect a digital voltmeter to the CN1561 (CN1611, CN1761, CN1861).
2. Press the [POWER] button to turn on the main power.
3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751, RV1801, RV1851) so that the digital voltmeter reading is 5 mV to 20 mV.

Huawei P7 – Disassembling procedure – How to replace the screen

Heat the glass panel on the back to around 85 Degree C so the adhesive loosens.
Use a plastic spudger or opening tool to gently pry up the glass.
Carefully work your way around the edges.
Be careful at the bottom. There is a flex cable running near the back-glass.
Never use metal tools for this. Metal will scratch the black paint off the back plate.
First, disconnect the battery cable.
Use a philips screwdriver to remove the shield, revealing the battery connection.
Next, disconnect the LCD/Digitizer ribbon.
Remove the battery.
Use plastic tools to pry the battery off its adhesive.
Don't bend, or heat the battery.
Heat the front side to about 85 Degree C.
Using a plastic tool, separate the display from the frame, but don't pull it too far away.
Flipping the phone over, can see the display ribbon.
Make sure none of this cable is stuck to the frame.
Pull the display ribbon through the frame.
If the screen broken while removing,make sure there is not a single glass-shard left on the frame. Any little splinter will cause significant damage to the new screen you're about to place.
Tape up the whole frame with double-sided tape for a perfect fit that won't become loose.
Put the new screen in.