How to replace the display of Sony Xperia Z - How to replace the display of Sony Xperia Z3

Sony Xperia display replacement procedure –Sony Xperia Z Display replacement procedure 

Warm the Battery cover before disassemble it.

Carefully' warm the battery and remove it. Be sure not to overheat the battery

Unscrew 4x screws and disconnect 3x flex cables in case to free the mother board.

Remove the mother board

Remove main Camera, front Camera and antenna wire Flex cable.

Remove The Headphone connector and the Ringer / Cover / Signal Antenna module.

Disconnect the LCD light flex cable by lifting up the black plastic and removing the flex

cable from the right side and we are ready to go.

Remove the touch panel . Warm the Touch screen before you start to disassemble it.

Sony Xperia Z3 Display replacement procedure 

Remove back cover. Slightly warm up the cover before removal

Then remove the back frame

Release LCD screen connector.

Remove the Digitizer and display after  Slightly warming up 

Heat up for 3 minutes, cut the sticker with much more effort and take the screen with earpiece on carefully

Remove the earpiece from screen. And need to put it back when place the new screen.

HP ENVY Sleekbook 6 – Disassembling procedure – How to remove the keyboard – How to remove the top cover – How to replace the battery

HP ENVY Sleekbook 6: disassembling procedure 

How to remove Base enclosure

Before disassembling the computer, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adaptor from the computer.
Remove the base enclosure:
1. Turn the computer face down, and then remove the 12 Phillips PM 7.5 millimeter long screws.

2. Remove the bottom enclosure.

How to remove Battery

Before removing the battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adaptor from the computer.

4. Remove the base enclosure 
Remove the battery:
1. Turn the computer right-side up, with the front toward you.

2. Disconnect the battery cable.

3. Move the battery cable to the side (1), and then remove the 6 Phillips PM 2.5×4.2 screws (2) that secure the battery to the computer.
4. Remove the battery from the computer (3).

How to remove Hard drive

Before removing the hard drive or SSD, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the base enclosure
5. Disconnect the battery cable
Remove the hard drive:
1. Disconnect the hard drive cable from the system board (1), and then remove the 4 screws (2) securing the hard drive to the top cover.

2. Remove the hard drive (3).

How to remove RTC battery

Before removing the RTC battery, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the base enclosure
5. Disconnect the battery cable 

Remove the RTC battery:
1. Use a thin, non-conductive tool to remove the RTC battery from the socket on the system board.

2. Hold down the media card reader board (2), and remove the RTC battery (3). (The RTC battery is also attached to the system board by foam material rather than double-sided adhesive.)

How to remove TouchPad module

Before removing the TouchPad button board, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the base enclosure
Remove the TouchPad button board and cable:
1. Turn the top cover upside down, with the back edge toward you.
2. Disconnect the cable (1) that secures the TouchPad cable to the system board.
3. Remove the 4 Phillips PM 2.5×3.0 black screws (2) that secure the TouchPad button board to the top cover.
4. Remove the 2 Phillips PM 2.5x3.0 silver screws, and then remove the TouchPad bracket (3).

5. Lift up on the rear edge, slide backwards, and then remove the TouchPad button board and cable (4).

How to remove rhe  Keyboard

Before removing the keyboard, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the base enclosure 

Remove the keyboard:
1. Turn the computer right-side up with the front facing you.
2. Remove the 16 Phillips PM 2x3 screws.

3. Remove the single screw (1), and then release the keyboard and keyboard bracket from the top cover (2).

4. Remove the 1 Phillips PM 2.5x3 screw securing the keyboard to the bracket (1), disconnect the keyboard cable (2) (pushing it through the bracket), and then remove the keyboard from the bracket (3)

How to remove Top cover

Before removing the top cover, follow these steps:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
4. Remove the base enclosure
5. Disconnect the battery cable
Remove the top cover:
1. Turn the computer right-side up, with the front toward you.
2. Open the computer.
3. Remove the 3 screws from each hinge on the top cover (1), and then remove the top cover (2).