How to disassemble LG WD-1247 BD washing machine-Exploded view

 

TEST OPERATION

WIRING DIAGRAM

Disassemble procedure

Unscrew 2 screws on the back of the top plate.
Pull the top plate backward and upward as shown.

Pull out the drawer and unscrew 2 screws.
Lift the side the Control Panel Assembly and pull it out

Push out PANEL ASSEMBLY,CONTROL after Push the hook below

Unscrew the 10 screws from the Control Panel Assembly.
Disassemble the Display PWB Assembly.

Disconnect connector from the wiring.

Two screws are unscrewed.

Push the hook of between BASE,CABINET and PWB ASSEMBLY below as shown.
Pull the PWB assembly (Main) to arrow direction.

Inlet valve removal

Disassemble the top plate assembly.
Pull out the drawer.
Push out the DISPENSER ASSEMBLY after unscrew 2 screws.

Unscrew the nut at the lower part of the dispenser.

Disassemble the 3 or 4 connectors from the valves.

① Red Housing(BK/WH-YL/BK)
② NA Housing(WH/BL-BK)
③ Blue Housing(GY/WH-BK)
④ Red Housing(BL/RD-BK)

Unscrew 2 or 4 screws from the back of the cabinet.

Unscrew 2 or 4 screws from the back of the cabinet.

Cabinet cover removal

Unscrew the 2 screws from the lower of the DECO PANEL.

Unscrew the 4 screws from the back of the DECO PANEL

Pull out the DECO PANEL

Unscrew the 4 screws from upper of the cabinet cover.
Unscrew the screw from filter cover.

Put a flat ( - ) screwdriver or putty knife into the both sides of the filter cover, and pull it out.

Unscrew the screw from the lower side of the cabinet cover.

Open the door.
Disassemble the clamp assembly.

Tilt the cabinet cover.
Disconnect the door switch connector.

NOTE: When assembling the CABINET COVER, connect the connector.

Lift and separate the cabinet cover.

Disassemble the clamp assembly.
Disassemble the Gasket.

Open the door.
Remove the two screws from the Hinge.
When removing the Door Assembly, it is necessary to hold the break is inner of the cabinet cover.

[Be careful: The door is heavy.]

Open the door and disassemble the CLAMP ASSEMBLY.
Unscrew the 2 screws.

NOTE: Reconnect the connector after replacing the DOOR SWITCH ASSEMBLY.

Disassemble the cabinet cover

Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly.
Disassemble the pump assembly in arrow direction.

Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly.
Disassemble the pump assembly in arrow direction.

CAUTION
• When assembling the heater, insert the heater into the heater clip on the bottom of the tub and check the position of wire color.
• Tighten the fastening nut so the heater is secure.

Disassemble the cabinet cover.
Unplug the white connector from the thermistor.
Pull it out by holding the bracket of the thermistor.

When foreign object is stuck between drum and tub

Disassemble the cabinet cover.
Separate the heater from the tub.
Remove any foreign objects (wire, coin, etc.) by inserting a long bar in the opening.

Disassemble the back cover.
Remove the bolt.
Pull out the Rotor.

Unscrew the 2 screws from the tub bracket.
Remove the 6 bolts on the stator.
Unplug the 2 connectors from the stator.

Disassemble the damper hinges from the tub and base.
Separate the dampers.

NOTE:  Once removed, replace the damper with new one.

To check out the fault diagnosis of TSG, in case of removing the water inside, you can pull out the plug and let the water drain away.

Be cautious in case of the TSG is hot temperature.

Remove the housing coupled the TSG (Heater, Water level frequency-sensor, Thermistor)

Taking out the screw of the TSG and Body Frame.

Taking out the screws of Body Frame (2EA)

Separate the hoses from the TSG.

Remove the Body Frame and then, separate the TSG from the washer.

Exploded view