Janome Sew
mini delux
FACE
COVER
1. Remove the face cover by removing the setscrew (A).
1. Remove the face cover by removing the setscrew (A).
FRONT
COVER
TO
REMOVE
1. Remove the face cover.
2. Pull out the dial and remove the set screws (A) - (E).
3. Loosen the set screws (F) - (G).
4. Remove the front cover.
NOTE: Do not remove the set screws (H).
TO ATTACH
5. Follow the above procedure in reverse.
1. Remove the face cover.
2. Pull out the dial and remove the set screws (A) - (E).
3. Loosen the set screws (F) - (G).
4. Remove the front cover.
NOTE: Do not remove the set screws (H).
TO ATTACH
5. Follow the above procedure in reverse.
ADJUSTING
THREAD TENSION
TO
ADJUST
1. Remove the face cover and the front cover.
2. Turn the adjusting screw (C) in the direction of (A) when the upper thread tension is too tight.
Turn the adjusting screw (C) in the direction of (B) when the upper thread tension is too loose.
3. Attach the front cover and the face cover.
TO CHECK
The standard upper thread tension should be 75 - 90g when pulling the thread (polyester thread #50) with setting the tension dial at “4”. (Make sure the foot should be lowered.)
If the tension is out of the standard range, adjust it as follows:
1. Remove the face cover and the front cover.
2. Turn the adjusting screw (C) in the direction of (A) when the upper thread tension is too tight.
Turn the adjusting screw (C) in the direction of (B) when the upper thread tension is too loose.
3. Attach the front cover and the face cover.
TO CHECK
The standard upper thread tension should be 75 - 90g when pulling the thread (polyester thread #50) with setting the tension dial at “4”. (Make sure the foot should be lowered.)
If the tension is out of the standard range, adjust it as follows:
ADJUSTING
NEEDLE DROP POSITION
The
clearance between the needle and side edges of the needle hole should be 0.2 mm
or more when the maximum width zigzag stitch is selecte. And the
neddle should drop in the center of the needle hole when the straight stitch
is selected.
TO ADJUST
1. Remove the face cover.
2. Select the straight stitch and the zigzag stitch.
3. Loosen the setscrew (A) and adjust the needle drop position by turning the eccentric pin (B).
NOTE: Adjust the direction of eccentric in the lower side.
4. Tighten the setscrew (A).
5. Attach the face cover.
TO ADJUST
1. Remove the face cover.
2. Select the straight stitch and the zigzag stitch.
3. Loosen the setscrew (A) and adjust the needle drop position by turning the eccentric pin (B).
NOTE: Adjust the direction of eccentric in the lower side.
4. Tighten the setscrew (A).
5. Attach the face cover.
ADJUSTING
NEEDLE SWING
TO
ADJUST
1. Remove the front cover.
2. Set the pattern selector dial at maximum zigzag width.
3. Loosen two setscrews.
4. Adjust the needle swing by turning the handwheel, while holding the worm so as not to rotate it, until the needle swing starts at 1.2mm above the needle plate after the needle has come out of the right side of the needle hole.
5. Tighten two setscrews.
6. Mount the front cover.
TO CHECK
Adjust the needle swing according to the following procedure, if the needle bar starts moving sideways while the needle is in the fabric when sewing the zigzag pattern (with maximum zigzag width).
1. Remove the front cover.
2. Set the pattern selector dial at maximum zigzag width.
3. Loosen two setscrews.
4. Adjust the needle swing by turning the handwheel, while holding the worm so as not to rotate it, until the needle swing starts at 1.2mm above the needle plate after the needle has come out of the right side of the needle hole.
5. Tighten two setscrews.
6. Mount the front cover.
TO CHECK
Adjust the needle swing according to the following procedure, if the needle bar starts moving sideways while the needle is in the fabric when sewing the zigzag pattern (with maximum zigzag width).
ADJUSTING
MOTOR BELT TENSION
The
correct motor belt tension is when the deflection of motor belt is about 7mm -
9mm.
(When pushing the motor belt by finger with a 100 gram load.)
TO ADJUST
1. Remove the face cover and front cover.
2. Loosen the setscrews (A) and (B) and adjust the deflection.
4. Tighten the setscrews (A) and (B).
(When pushing the motor belt by finger with a 100 gram load.)
TO ADJUST
1. Remove the face cover and front cover.
2. Loosen the setscrews (A) and (B) and adjust the deflection.
4. Tighten the setscrews (A) and (B).
