BenQ MX613ST
Replacing the
lamp
• To reduce
the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
• To reduce
the risk of severe burns, allow the projector to cool for at least 45 minutes before
replacing the lamp.
• To reduce
the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
• To reduce
the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
• This lamp
contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner.
• To assure
optimal performance from the projector,it is recommended that you purchase a
qualified projector lamp for lamp replacement.
• If lamp
replacement is performed while the projector is suspended upside-down from the
ceiling, make sure that no one is underneath the lamp socket to avoid any possible
injury or damage to the human eyes caused by fractured lamp.
1. Turn the
power off and disconnect the projector from the power outlet. If the
lamp is hot, avoid burns by waiting for approximately 45 minutes until the
lamp has cooled.
2. Loosen the
screw(s) that secures the lamp cover on the side of the projector until
the lamp cover loosens
3. Remove the
lamp cover from the projector.
• Do not turn
the power on with the lamp cover removed.
• Do not
insert your fingers between the lamp and the projector. The sharp edges
inside the projector may cause injuries.
4. Disconnect
the lamp connector from the projector as illustrated.
5. Loosen the
screw that secures the lamp.
6. Lift the
handle so that it stands up
7. Use the
handle to slowly pull the lamp out of the projector.
• Pulling it
too quickly may cause the lamp to break and scatter broken glass in the
projector.
• Do not place
the lamp in locations where water might splash on it, children can reach
it, or near flammable materials.
• Do not
insert your hands into the projector after the lamp is removed. If you
touch the optical components inside, it could cause color unevenness and
distortion of the projected images.
8. Lower the new lamp
9. Tighten the
screw that secures the lamp.
10. Ensure the
handle is fully laid flat and locked in place.
11. Reconnect
the lamp connector.
• Loose screw
may cause a bad connection, which could result in malfunction.
• Do not over
tighten the screw
12. Replace
the lamp cover on the projector.
13. Tighten
the screw(s) that secures the lamp cover.
• Loose screw
may cause a bad connection, which could result in malfunction.
• Do not over
tighten the screw.
14. Connect
the power and restart the projector. Do not turn the power on with the
lamp cover removed.
Resetting the lamp
timer
15. After the
start up logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced> Lamp Settings menu. Press MODE/ENTER. The Lamp
Settings page displays. Highlight Reset Lamp Timer. A warning message is
displayed asking if you want to reset the lamp timer. Highlight Reset
and press MODE/ENTER. The lamp time will be reset to “0”. Do not
reset if the lamp is not new or replaced as this could cause damage.
BenQ W1080, W1070
Replacing the
lamp
• To reduce
the risk of electrical shock, always turn the projector off and disconnect the
power cable before changing the lamp.
• To reduce
the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
• To reduce
the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
• To reduce
the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is
removed.
• This lamp
contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner. Status Message Install a new lamp for
optimal performance. If the projector is normally run with Economics
elected , you may continue to operate the projector until the next
hour lamp warning appears. Press MODE/ENTER to dismiss the
message. It is strongly recommended that you replace the lamp at this
stage. The lamp is a consumable item. The lamp brightness diminishes with use.
This is normal lamp behavior. You can replace the lamp whenever you notice
that the brightness level has significantly diminished. Press
MODE/ENTER to dismiss the message. The lamp MUST be replaced before the
projector will operate normally. Press MODE/ENTER to dismiss the
message.
1. Turn the
power off and disconnect the projector from the power outlet. If the lamp is
hot, avoid burns by waiting for approximately 45 minutes until the lamp has
cooled.
2. Loosen the
screw that secures the lamp cover on the side of the projector until the
lamp cover loosens.
3. Remove the
lamp cover from the projector.
• Do not turn
the power on with the lamp cover removed.
• Do not
insert your fingers between the lamp and the projector. The sharp edges
inside the projector may cause injuries.
4. Loosen the
screw that secures the lamp.
5. Lift the
handle so that it stands up.
6. Use the
handle to slowly pull the lamp out of the projector.
• Pulling it
too quickly may cause the lamp to break and scatter broken glass in the
projector.
• Do not place
the lamp in locations where water might splash on it, children can reach
it, or near flammable materials.
• Do not
insert your hands into the projector after the lamp is removed. If you
touch the optical components inside, it could cause color unevenness and
distortion of the projected images.
7. Lower the
new lamp.
8. Tighten the
screw that secures the lamp.
9. Ensure the
handle is fully laid flat and locked in place.
• Loose screw
may cause a bad connection, which could result in Malfunction.
• Do not over
tighten the screw.
10. Replace
the lamp cover on the projector.
11. Tighten
the screw that secures the lamp cover.
• Loose screw
may cause a bad connection, which could result in malfunction.
• Do not over
tighten the screw.
12. Connect
the power and restart the projector.
Resetting the
lamp timer
Do not reset
the lamp timer if the lamp has not been replaced as this could cause damage.
13. After the
start-up logo, press MENU/EXIT and then press / until the System Setup : Advanced
menu is highlighted.
14. Press to
highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page displays.
15. Highlight
Reset Lamp Timer and press MODE/ENTER. A warning message displays asking if you
want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp
time will be reset to "0".
