How
to remove the top cover - how to remove the keyboard – How to remove the
battery
HP SlateBook 14 DISASSEMBLING PROCEDURE How to remove Computer feet
Before
replacing the computer feet, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the computer feet:
1. Close the computer.
2. Turn the computer upside down with the front toward you.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove the computer feet:
1. Close the computer.
2. Turn the computer upside down with the front toward you.
3. Remove
the 4 rubber feet
How
to remove Keyboard/top cover
Before
replacing the keyboard/top cover, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
Remove
the keyboard/top cover:
1. Close the computer.
2. Turn the computer upside down with the front toward you.
3. Remove the rear rubber feet (1).
4. Remove the oblong rubber screw covers (2).
2. Turn the computer upside down with the front toward you.
3. Remove the rear rubber feet (1).
4. Remove the oblong rubber screw covers (2).
5. Remove
the round rubber screw cover (3)
6. Remove
the thirteen Phillips PM1.9×5.7 screws that secure the keyboard/top cover to
the base enclosure.
7. Turn
the computer right side up.
8. Open
the computer as far as it will open.
9. Detach the front edge of the keyboard/top cover (1) from the base enclosure.
10. Lift the keyboard/top cover (2) until it rests at an angle.
11. Disconnect the battery cable (3) from the system board.
12. Release the zero insertion force (ZIF) connector (4) to which the power button board cable is attached, and then disconnect the power button board cable from the system board.
13. Release the ZIF connector (5) to which the keyboard cable is attached, and then disconnect the keyboard cable from the system board.
9. Detach the front edge of the keyboard/top cover (1) from the base enclosure.
10. Lift the keyboard/top cover (2) until it rests at an angle.
11. Disconnect the battery cable (3) from the system board.
12. Release the zero insertion force (ZIF) connector (4) to which the power button board cable is attached, and then disconnect the power button board cable from the system board.
13. Release the ZIF connector (5) to which the keyboard cable is attached, and then disconnect the keyboard cable from the system board.
14. Release the ZIF connector (6) to which the TouchPad board
cable is attached, and then disconnect the TouchPad board cable from the system
board.
15. Remove
the keyboard/top cover (7) by sliding it away from the computer at an
angle.
How
to remove TouchPad
Before
replacing the TouchPad, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove the TouchPad:
1. Turn the keyboard/top cover upside down with the front toward you.
2. Remove the two Phillips PM1.9×2.1 broad head screws (1) that secure the TouchPad to the keyboard/top cover.
3. Press on the tab (2) on the back of the TouchPad to release the ToucPad from the keyboard/ top cover.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove the TouchPad:
1. Turn the keyboard/top cover upside down with the front toward you.
2. Remove the two Phillips PM1.9×2.1 broad head screws (1) that secure the TouchPad to the keyboard/top cover.
3. Press on the tab (2) on the back of the TouchPad to release the ToucPad from the keyboard/ top cover.
4. Remove
the TouchPad (4).
How
to remove USB board
Before
replacing the USB board, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove the USB board:
1. Release the ZIF connector (1) to which the USB board cable is attached, and then disconnect the
USB board cable from the system board.
2. Detach the USB board cable (2) from the battery. (The USB board cable battery is attached to the battery with double-sided adhesive.)
3. Remove the two Phillips PM1.9×2.1 broad head screws (3) that secure the USB board to the base enclosure.
4. Remove the USB board (4) and cable.
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove the USB board:
1. Release the ZIF connector (1) to which the USB board cable is attached, and then disconnect the
USB board cable from the system board.
2. Detach the USB board cable (2) from the battery. (The USB board cable battery is attached to the battery with double-sided adhesive.)
3. Remove the two Phillips PM1.9×2.1 broad head screws (3) that secure the USB board to the base enclosure.
4. Remove the USB board (4) and cable.
How
to remove Battery
Before
replacing the battery, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove
the battery:
1. Remove the eight Phillips PM1.9×2.8 screws (1) that secure the battery to the base enclosure.
2. Detach the USB board cable (2) from the battery. (The USB board cable battery is attached to the battery with double-sided adhesive.)
3. Lift the front edge of the battery (3) until it rests at an angle.
1. Remove the eight Phillips PM1.9×2.8 screws (1) that secure the battery to the base enclosure.
2. Detach the USB board cable (2) from the battery. (The USB board cable battery is attached to the battery with double-sided adhesive.)
3. Lift the front edge of the battery (3) until it rests at an angle.
4. Remove
the battery (4) by sliding it up and forward at an angle
5. Remove
the battery.
How
to remove Display assembly
Before
replacing the display assembly, follow these steps:
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove the display assembly:
1. Disconnect the display panel cable (1) from the system board.
2. Disconnect the WLAN antenna cable (2) from the terminal on the WLAN module.
3. Release the WLAN antenna cable from the clip (3) built into the base enclosure.
4. Remove the two Phillips PM1.9×2.8 screws (4) that secure the display assembly system board to the base enclosure.
5. Remove the display assembly (5)
1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
2. Disconnect the power from the computer by unplugging the power cord from the computer.
3. Disconnect all external devices from the computer.
4. Remove the keyboard/top cover
Remove the display assembly:
1. Disconnect the display panel cable (1) from the system board.
2. Disconnect the WLAN antenna cable (2) from the terminal on the WLAN module.
3. Release the WLAN antenna cable from the clip (3) built into the base enclosure.
4. Remove the two Phillips PM1.9×2.8 screws (4) that secure the display assembly system board to the base enclosure.
5. Remove the display assembly (5)
