Wednesday, 25 October 2017

Apple iPhone 7 - Specification - Disassembling procedure

Specification
1. Apple A10 Fusion processor with embedded M10 motion coprocessor
2. 32, 128, or 256 GB onboard storage capacity
3. 4.7-inch IPS multitouch Retina HD display with 1334 × 750 pixels (326 ppi)
4. 12 MP camera with f/1.8 aperture, optical image stabilization, and 5x digital zoom
5. 7 MP FaceTime HD camera with f/2.2 aperture and 1080p HD recording capability
6. Non-mechanical Touch ID home button driven by new Taptic Engine
7. 802.11a/b/g/n/ac Wi Fi + MIMO Bluetooth 4.2 + NFC
As you oppen iPhone 7,a few new additions on the surface:
A 1334-by-750, LED-backlit IPS display with a P3 color gamut and 25% higher brightness than that of the 6s.
An f/1.8, 12 MP camera with built-in optical image stabilization. Apple claims it's 60% faster and 30% more efficient than the previous generation.
A quad-LED True Tone flash that's 50% brighter than the iPhone 6s.

The iPhone 7 shares exact dimensions (138.3 mm × 67.1 mm × 7.1 mm) with its predecessor, the iPhone 6s-but has dropped a little weight, coming in at 138 grams compared to the 143 grams of the iPhone 6s.
DISASSEMBLING PROCEDURE
Power off your iPhone before beginning disassembly.
Remove the two 3.6 mm Pentalobe screws next to the Lightning connector.
If the plastic depth gauge is attached at the center of the Sclack, remove it now -it's not needed for larger phones like the iPhone 7.
Close the handle on the Sclack, opening the suction cup jaws.
Place the bottom of your iPhone in between the suction cups.
Position the Sclack's upper suction cup against the display, near the home button.
Open the handles to close the jaws of the Sclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone
After briefly fighting through some sticky adhesives to open the case, you faced with another set of repair obstacles teeny tiny tri-point screws securing the cable bracket etc
With the front panel and strings of sticky glue out of the way, you can whip out our trusty spudger and disconnect the battery. Next, it's time to set our spudger to the task of popping off display connectors.
The iPhone 7 camera boasts a larger f/1.8 aperture, new 6-element lens and 12 MP sensor, four LEDs, and a flicker sensor that can sense flickering light and compensate for it in your photos and videos.
With the new camera out of the way, You can work our way deeper into the 7.
Next out: the audio baffle that thinks it's a headphone jack.
According to Apple, this plastic component is a barometric vent. With the added ingress protection afforded by the watertight seal, the iPhone uses this baffle to equalize the internal and atmospheric pressures in order to have an accurate altimeter.
This Taptic Engine takes advantage of its extra legroom, sizing up for its home button haptic duties.
With the path cleared, you can  use handy spudger to release the adhesive from beneath the battery.Wind up and peel out the three battery pull tabs.
The iPhone 7's power source.
Actually, it's a relatively benign Lithium-ion battery. This 3.8 V, 1960 mAh battery is rated for a capacity of 7.45 Wh.
Apple claims that this upgraded cell will provide up to 14 hours of 3G talk time, 14 hours of Wi-Fi internet browsing, and 10 days of standby.

LG 52LG50FD, 52LG50FD-SA-Service adjustments-service mode entry-white balance adjustment-ADC component 1 RGB adjustment and more

  These adjustments are similar to 42LB7DF Because this is not a hot chassis, it is not necessary to use an isolation transformer. However...