LG frond load Washing Machine - error codes – Error code description, cause and solution

ERROR CODE CE
The CE error code indicates there has been an over-current in the electrical circuit of the motor caused by a short circuit, loose connection, ground fault, or power surge.
1. Unplug the washer for 10 seconds.
2. Plug the washer back in and attempt to run a cycle.
If the CE error code persists, close the water taps and unplug the washer; the unit will require repair
ERROR CODE Cd
Cd is not an error code, but an indicator that the drying cycle is completed, (Cool Down) is displayed on the Multi display. Cool Down is set automatically when the drying cycle is complete. If clothes are not removed promptly when the drying cycle ends, wrinkles can form.
The Cool Down feature periodically tumbles, rearranges and fluffs the load to avoid wrinkles for up to 4 hours. The message will continue to display until the clothes are removed or the Start/Pause button is pressed.
ERROR CODE CL
CL is not an error code, but an indicator that the child lock feature is active. To activate or de-activate child lock, press and hold the Child Lock button for 3 seconds.

ERROR CODE dE

A dE error code means the washer was not able to lock the door. This might be a result of: The door is not completely closed The door is misaligned A defective door latch Troubleshooting:

1. Press POWER and turn the washer OFF.

2. Unplug the washer

3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.

4. Plug the washer back in.

5. Power the unit back ON.

6. Press in on the door firmly.

7. Select any cycle and press START/PAUSE.

To prevent future occurrence of the dE error:

Avoid putting weight on or pushing down on the door while it's open. Putting strain on the door hinge could cause a misalignment. Always place items in the drum completely so that sleeves and the corners of fabric aren't trapped between the door glass and gasket.

ERROR CODE dE1

The dE1 error code indicates that the washer door is open and not locking.

1. Unplug the washer for 10 seconds.

2. Plug the washer back in, making sure the door is completely closed and restart the cycle.

ERROR CODE dE2

The dE2 error code indicates that the washer door is closed, but not locking.

1. Unplug the washer for 10 seconds.

2. Plug the washer back in, making sure the door is completely closed and restart the cycle.

ERROR CODE FE

The FE error code indicates that the washer is overfilling. This is usually a result of a faulty water valve.

1. Close both water taps.

2. In order to drain out any trapped water, power the washer back on and press the Spin Speed button until No Spin is selected and press the Start/Pause button.

3. Once the washer has drained, restart the wash cycle.

ERROR CODE IE

An IE error code means the washer wasn't able to fill with water. This is likely caused by:

# Closed supply taps

# Kinked inlet hoses

# Clogged inlet filters

# Faulty Hot or Cold inlet valves.

ERROR CODE LE

An LE error code on the washer's display indicates that the motor is locked, possibly due to a heavy wash load.

ERROR CODE PE

The PE error code indicates that the water level sensor has malfunctioned.

1. Unplug the washer for 10 seconds.

2. Plug the washer back in and restart the cycle.

ERROR CODE PF

The PF error code indicates a power failure. This can occur if the power to the washer is interrupted during a cycle from a power outage.

ERROR CODE tE

The tE error code indicates a heating error, usually caused by a faulty thermistor.

1. Unplug the washer for 10 seconds.

2. Plug the washer back in and press Power button and then the Spin Speed button until No Spin is highlighted.

3. Once the washer has drained, restart the wash cycle.

ERROR CODE UE

The UE code to indicates an unbalanced load. The size and type of wash load can cause the washer to become unbalanced. Small Wash Load

1. The weight of the load must be evenly distributed across the surface of the drum for proper operation.

2. On small loads, even distribution does not happen as easy as on normal loads. Clothing will clump together throwing the weight of the drum off during the spin cycle.

3. Rearrange the items in the drum, and restart the spin cycle.

Mixed Fabric Load

1. Mixed fabric loads (such as jeans and t-shirts) can cause unbalanced rotation of the drum.

2. For Example: When washing jeans and t-shirts, jeans could be on one side of the drum and t-shirts on the other.

3. Rearrange the items in the drum, and restart the spin cycle.

How to program the remote RCA RCR503BR – Codes list for television

Direct code Entry
1. Manually turn on the component you wish to program the remote to operate.
2. Find the four-digit code for your brand of TV.
3. Press and hold the CODE SEARCH key until the indicator light turns on.
4. Release the CODE SEARCH key.
5. Press and release the TV key. The indicator light blinks and then remains lit.
6. Enter the four-digit code, using the numeric keypad. After the code is entered, the indicator light turns off.
Note: If the indicator light blinks multiple times, you’ve entered an invalid code. Start from step 2 again.
7. Aim the remote at the component and press the ON,OFF key. The component should turn off.
Code Search method
1. Manually turn on the component you wish to program the remote to operate.
2. Press and hold the CODE SEARCH key until the indicator light turns on.
3. Release the CODE SEARCH key
4. Press and release the component key you wish the remote to control TV, VCR,DVD or SAT,CBL,DTC key. The indicator light blinks once and remains lit.
Important: Find the ENTER key on your remote (don't press it yet). You will need to press this key quickly in step 6 below.
5. Press and release the ON,OFF key until the component turns off.
Important: You may have to press the ON,OFF key up to 200 times.
6. As soon as the component turns off, press the ENTER key within 4 seconds. The indicator light turns off.
CODE LIST FOR TELEVISION 
 A
Admiral  0093, 0463
Advent  0761
Akai  0812, 1675, 0702, 1935
AOC  1365, 1589, 2014, 2087, 2479
Apex Digital  0748, 0765, 1217, 2397
Audiovox 0451, 0802, 1766, 1769, 1868,2121
Aventura  0171
B
Broksonic  0463, 1935,
C
Carver  0054
Celebrity 0001
Celera  0765
Changhong  0765
Citizen  0060, 1935,
Coby  1634, 2306, 2315, 2344, 2345, 2348
Commercial Solutions  1447, 0000
Crosley 0001, 0054
Curtis  2352, 2466
Curtis Mathes  0000, 0054, 0451, 0093,0060, 0702, 0145, 1661
D
Daewoo 0451,1661
Dell  1264
Denon  0145
Dumont  0017
Durabrand  0463, 0178, 0171
Dynex  1463, 2049, 2184
E
Electroband  0001
Electrograph  1755
Electrohome  0463, 1670
Element  1687, 1886, 2183
Emerson  1864, 0451, 0463, 0178, 0171,1661, 1394, 1665, 1963
Emprex  1422
Envision  1365, 1589, 2014, 2087
ESA  0812, 0171, 1963
F
Funai  0001, 0171, 1963
G
Gateway  1755
GE  1547, 1447, 0000, 0051, 0451, 0178
GFM  0171, 1665, 1963, 2167
Gibralter 0017
GoldStar  0178
H
Haier 1748, 1749, 2309
Hallmark  0178
Hannspree 1348
Harman/Kardon  0054
Havermy  0093
Hello Kitty  0451
Hisense  0748, 1660, 2098, 2355
Hitachi  1643, 0145
I
iLo 1394, 1665, 1684
Infinity 0054
Insignia 1423, 1564, 0463, 0171, 1660,1710, 1892, 1963, 2049
Inteq  0017
J
JBL  0054
JCB  0001
Jensen  0761
JVC 0463, 0053, 1253, 1601, 1774, 2264
K
KDS  1498, 1687
KLH  0765
L
LG  1423, 1447, 0017, 0178, 2358, 2424
LXI  0000, 0054, 0156, 0178
M
MAG  1498, 1687
Magnavox  1454, 1866, 1755, 0054, 0051,0171, 0802, 1365, 1856, 1963, 2372
Marantz  1454, 0054
Matsushita  0250
Maxent  1755
MB Quart  1868
Megatron  0178, 0145
Memorex 0463, 0150, 0178, 1670, 1892
MGA  0150, 0178
Midland 0000, 0017, 0051
Mitsubishi  1250, 0093, 0150, 0178
Motorola  0093
MTC  0060
N
NAD  0156, 0178
NEC  1797
NetTV  1755
Nexus Electronics  2183
Nikko  0178
Norcent  0748, 1365, 1589
O
Olevia  1610, 1240, 1331
Optimus  0250
Optoma  1348
Optonica  0093
Orion  0463, 1463
P
Panasonic  1480, 0250, 1457, 0051, 1291,2264
PARK  2104, 2194
Penney  0000, 0156, 0051, 0060, 0178
Petters  1523
Philco 0054, 0171, 1394, 1665, 1963
Philips  1454, 1866, 0054, 1744, 1856,2372,2374
Pioneer  1457
Polaroid 1523, 0765, 1276, 1498, 1687,1766, 1769, 2121
Portland  0451, 1661
Prima  0761
Prism 0051
Proscan  1447, 0000, 2256
Proton  0178
Proview  1498, 1687
Pulsar 0017
Q
Quasar  0250, 0051
R
RadioShack  0000, 0178
RCA 1547, 1447, 0000, 0051, 0093, 1661,1781, 2187, 2247, 2434,
Realistic  0178
Runco  0017
S
Sampo  1755
Samsung 0812, 0060, 0702, 0178,1060,2051
Sansui  0463, 0171, 1670, 1892, 1935
Sanyo 0054, 1142
Sceptre  0878, 1217, 1360, 1599, 2506
Scotch  0178
Scott  0178, 1711
Sears  0000, 0054, 0156, 0178, 0171
Sharp  0818, 0093
Sheng Chia  0093
Signature  0054
Sony 0001
Soundesign  0178
Soyo 1826
Spectroniq 1498, 1687
Squareview  0171
Superscan  0093
Supreme  0001
SVA  0748, 1963
Sylvania  1864, 0054, 0171, 1394, 1665,1886, 1963
Symphonic  0171
Syntax 1610, 1240, 1331
T
Tandy 0093
Technics  0250, 0051
Techwood  0051
Teknika 0054, 0150, 0060
Telefunken  0702
TMK  0178
TNCi  0017
Toshiba1524, 0156, 0060, 1291, 1935 ,2006
TVS  0463
V
Victor 0053
Vidikron  0054
Vidtech  0178
Viewsonic  1755, 0885, 1330, 1365, 1578,1627, 1640, 1742, 2014, 2087, 2277
Viore 1684, 2104, 2352
Vizio  1758, 0885
W
Wards  0001, 0000, 0054, 0017, 0156,0051,0060, 0178
Waycon  0156
Westinghouse  1712, 0451, 0885, 1217
White Westinghouse  0463,1661
Wyse  1365
Z
Zenith  0001, 1423, 0000, 0017, 0463,0178, 0145, 1661, 1365

How to set idle current adjustments – Sony STR DA5800AS, key-test, Reset

Sony STR-DA5800ES – Factory reset,  Key check mode, Idle current adjustment procedure

Factory preset mode
Procedure
1. While pressing the [TUNING] and [2CH/A.DIRECT] buttons, press the [POWER] button to turn on the main power.
2. The message “Factory Preset” appears and specific preset values are set.

Sound field clear mode
The preset sound field is cleared when this mode is activated.
Procedure
1. While pressing the [MUSIC] button, press the [POWER] button to turn on the main power.
2. The message “S.F. Initialize” appears and initialization is performed.

Fluorescent indicator tube display test

All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another.
Procedure
1. While pressing the [TONE] and [A.F.D.] buttons, press the [POWER] button to turn on the main power.
2. All segments and all LEDs turn on.

Swap mode
The signal will be swap to all channel so that all speaker will have sound output.
Procedure:
1. While pressing the [MEMORY/ENTER] and [2CH/A. DIRECT] buttons, press the [POWER] button to turn on the mainpower.
2. The message “SWAP MODE !” appears (No change while displayed).

SETTING LOCK ON/OFF CHANGE MODE
All the settings can be locked.
Procedure:
1. While pressing the [SPEAKERS A/B/A+B/OFF] and [MUSIC] buttons, press the [POWER] button to turn on the main power.
2. The message “SETTINGS LOCK [ ON]” appears.

Releasing method
1. While pressing the [SPEAKERS A/B/A+B/OFF] and [MUSIC] buttons, press the [POWER] button to turn on the main power.
2. The message “SETTINGS LOCK [OFF]” appears.

Command mode change mode

The command mode of the remote-commander which this set receives can be changed.

Procedure:

1. While pressing the [2CH/A. DIRECT] button, press the [POWER] button to turn on the main power.

2. Either the message “COMMAND MODE [AV1]” or “COMMAND MODE [AV2]” appears. Select the desired mode.

Software version display mode

The software version is displayed.

Note: In this mode, never press the [UP] and [DOWN] buttons on the remote commander.

Procedure:

1. While pressing the [TONE] and [MUSIC] buttons, press the [POWER] button to turn on the main power.

2. The model name/destination/system controller software version appears. Each time the [DISPLAY MODE] button is pressed, the version is switched in order.

(Displayed characters/values in the following figure are example)

Releasing method:

Press the [POWER] button to turn off the main power.

Rebox test mode

Displayed the number of times of the power on after the shipment.

Procedure:

1. While pressing the [A.F.D.] and [SPEAKERS A/B/A+B/OFF] buttons, press the [POWER] button to turn on the main power.

2. The number of times of the power on after the shipment appears.

Releasing method:

Press the [POWER] button to turn off the main power.

Key check mode

Each buttons can be checked.

Procedure:

1. While pressing the [MEMORY/ENTER] and the [MOVIE/HD-D.C.S.] buttons, press the [POWER] button to turn on the main power.

2. Either the message “REST 17” appears.

Every pressing of any button other than the [POWER] counts down the buttons.

(The buttons which are already counted once are not counted again)

3. When all buttons are pressed “REST 00” appears.

Releasing method:

Pull out the power cord, or do not perform operation for 10 seconds.

Special menu mode

Various version displays of system, update, test, etc. can be performed.

Setting method:

1. Press the [POWER] button to turn on the main power.

2. While pressing the [TONE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE/HD-D.C.S.] button in order, the message “MENU SPECIALIZED !” appears.

3. Press the [AMP MENU] button of the remote commander, the message “<<< SPECIAL >>>” appears.

4. Press the [RIGHT] button of the remote commander, the item is appears.

5. Each time the [UP] or [DOWN] buttons of the remote commander is pressed, the item is switched in order of “Display of special menu mode”.

Some items can change the content. Display the cursor by pressing the [RIGHT] button of the remote commander, and changing the content by pressing the [UP] or [DOWN] buttons of the remote commander, and fix the content by pressing the [POWER] button of the remote commander when you want to change the content of the item.

Idle current adjustment

Note: After 10 minutes or more have passed since the power supply was turned on, this adjustment is done.

Connection:

CN1561 (CN1611, CN1761, CN1861, CN4441, CN4491) pin 1, CN1561 (CN1761, CN1861) pin 3 – Positive terminal of digital voltmeter

CN1561 (CN1611, CN1761, CN1861, CN4441, CN4491) pin 2, CN1561 (CN1761, CN1861) pin4 - Negative terminal of digital voltmeter

Note: Pin 3, 4 of CN1611, CN4441, CN4491 are open.

Procedure:

1. Connect a digital voltmeter to the CN1561 (CN1611, CN1761, CN1861, CN4441, CN4491).

2. Press the [POWER] button to turn on the main power.

3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751, RV1801, RV1851, RV4421, RV4471) so that the digital voltmeter reading is 5 mV to 20 mV.

Note: Adjust for the digital voltmeter reading to become 5 mV as much as possible.

How to calibrate the treadmill – How to access Engineering mode - Spirit Z 900 treadmill

Spirit Z 900 treadmill calibration and engineering mode entry procedure
Calibrating the unit
1. Remove tether cord.
2. Press and hold the START and FAST buttons. Replace the tether cord while maintaining the buttons. Display will show “FACTORY SETTING”. Press ENTER.3. Units English / Metric. Press UP or DOWN to change. Press ENTER.
4. Adjust wheel diameter using UP or DOWN. Should be 2.75. Press ENTER.
5. Adjust minimum speed to 0.5 using UP and DOWN. Press ENTER.
6. Adjust maximum speed to 12 using UP and DOWN. Press ENTER.
7. Adjust maximum elevation to 15 using UP and DOWN.
8. Press START to begin calibration. DO NOT STAND ON BELT DURING CALIBRATION.
Checking wire harness for continuity
1. Set your multimeter to read ohms.
2. Place the test leads at opposite ends of the wire, make sure both leads are on the same wire and are in contact with metal.
3. If the reading is close to 0 ohms, the wire has continuity (unbroken).
4. If the reading is very high or there is no reading at all, there is no continuity.
5. If there is no continuity, the harness needs to be replaced.
Speed sensor adjustment

1. Take off the motor hood.
2. The speed sensor is located on the frame, near where the drive belt goes around the front roller.
3. The sensor should be adjusted to about 1/16th of an inch from the front roller.

Checking treadmill circuit breaker

1. The circuit breaker is a small, red button between the power cord and the power switch.
2. Press the button in to reset.

Check roller for magnet
1. The front roller should have a round magnet and a round counter weight.
2. Take a screw or something metallic and test each one.
3. Only one should be magnetic.
Adjust Torque Boost
1. Using a small screw driver, turn the dial counter clockwise until it stops.
2 Press the START button on the console.
3. With someone standing on the walking belt, turn clockwise until the belt begins to move.
4. Increase the speed and check for smooth belt movement.
Replacing controller
1. Disconnect power cord from unit.
2. Remove motor hood.
3. Remove two Phillips screws holding in the controller.
4. Disconnect all wires connected to the controller.
5. Insert new controller, secure with Phillips screws.
6. Reconnect wires to controller. 
Replacing wire harness
1. Turn power switch off.
2. Unplug harness from console and controller.
3. Tie the end of the new harness to the old harness (with a zip-tie or spare wire).
4. As you pull the old harness out of the upright, you will pull the new harness in.
5. Connect to board and console, & turn power back on.

Replacing drive motor

1. Turn power switch off.
2. Disconnect red and black motor wires from controller.
3. Loosen tension bolt and remove four motor bolts.
4. Take off drive belt.
5. Insert new motor into place.
6. Put drive belt on.
7. Put in four motor bolts. Do not tighten them all the way down.
8. Tighten the tension bolt until you only have about an inch of play in the drive belt.
9. Tighten down the four motor bolts.
10. Plug the motor wires into the controller.

Replacing incline motor

1. Turn power switch off.
2. If possible, fold up unit.
3. Turn treadmill onto its side.
4. Disconnect motor wires from controller.
5. Remove bolt from incline tube.
6. Remove bolt from top of incline motor and take out motor.
7. Insert new motor and put in bolt on the top.
8. Reconnect motor wires to controller.
9. Turn on unit. The new motor should turn until it is at “zero”.
10. Insert bolt into incline tube.

Engineering mode

1. Remove the tether cord.
2. Press and hold the START, ENTER, and STOP buttons and replaced the tether cord.
3. The display will say ENGINEERING MODE. Press ENTER.
4. Press the UP and DOWN buttons to scroll through the following sub menus:
*Calibration
*Factory Settings
*Security
*Functions
*Display Test
*Key Test

5. Press ENTER to access the desired program.

* Calibration Speed Calibration – In this mode, you can test the speed.

* Incline Calibration – In this mode, you can test the incline.

* Factory Settings - This mode will allow you to view the Wheel size, Max inc, Max and Min speed.

Use the UP and DOWN buttons to scroll through. (They cannot be changed here)

* Security Child Lock On/Off

Press ENTER to turn on or off. To unlock display, press START and ENTER.

* Functions Sleep Mode On/Off - Press ENTER to turn on or off.

Units English/Metric -  Press ENTER to change.

Maintenance

Lube Message Reset - Press ENTER to reset. 

Odometer Reset -  Press ENTER to reset.

Pause Mode On/Off -  Press ENTER to turn on or off.

Display Test - Test all LED’s

Key Test - Test all buttons on console.

LCD TV SMPS schematic - Delta DPS 77PA

Used ICs and FET - DDA009DWR, ICE2Q03G, IN4D101-T6G, SPA11N80C3(FET)

How to enter service mode, service adjustments – Beko TFT LCD TV – LC and L5C chassis

Color TFT LCD Module is very sensitive both electrically and physically. Users, therefore, are requested to follow the “Guidance of handling color TFT LCD Module”
LC (L5C) SERVICE MENU
Service Menu is entered by pressing 9, 3, 0, 1 key on the remote controller when the Picture icon is highlighted in the Main Menu.
Service Menu has 3 sub-menus. These are:
* Options
* Adjustments
* Selections.
Navigation through these menus can be done by pressing OK button. Every adjustment made in this menu is saved automatically.
OPTIONS
Options are adjustments that the user can select On or Off.
* SCART 2
* FAV
* SVHS
* HOTEL MODE
* STAND BY
* MSP CARRIER MUTE
* WSS SCART

* FIRST ATS

SCART 2 / FAV / SVHS

If a source is disabled in the Service Menu, it will be skipped during source switches. If SCART2 is enabled, SW assumes that the FAV source share the same path as the SVHS source on the HW. If it is disabled, it is assumed that FAV and SVHS share separate paths. TUNER and SCART1 are enabled by default.

HOTEL MODE

Enabling Hotel Mode has two effects. First, SETUP menu is no longer accessible by the user. Second, maximum adjustable volume value is limited to HOTEL VOLUME value. This value can be adjusted in the ADJUSTMENTS sub-menu of the Service Menu.

STAND BY

If this Option is OFF, the TV will stay in Stand By mode after a Power On. If this Option is ON, the TV will recall its last stand by status before the Power Off, and switch on from Stand By automatically, if the last state was ‘Stand by On’.

MSP CARRIER MUTE

If this option is ON, sound processor’s carrier mute functionality will be enabled. The MSP will mute the sound automatically if the signal quality is bad. Setting this option Off will disable this functionality.

ATS

If this option is set to ON, TV will display Country Selection menu in the next start. After some country is selected, the user will be prompted for the start of Auto Programming process.

ADJUSTMENTS

This sub-menu contains numeric adjustments. These items are:

* WHITE R

* WHITE G

* WHITE B

* BRIGHTNESS

* CONTRAST

* COLOR

* PRESCALE FM

* PRESCALE NICAM

* PRESCALE SCART

* HOTEL VOLUME

WHITE R / WHITE G / WHITE B

These are used for color bias adjustment. Unlike other items in the service menu, changes will take effect immediately.

PRESCALE FM / PRESCALE NICAM / PRESCALE SCART

These are prescale values that will be used for the initialization of the sound processor (MSP), at the next switch on.

HOTEL VOLUME

This value is used as the volume limit, when the Hotel Mode is on.

SELECTIONS

This sub-menu contains selections.

* TUNER TYPE SAMSUNG / PHILIPS

* TELETEXT NO TEXT / FAST / FAST&TOP

* MSP CLIP REDUCE VOL / REDUCE TONE

TUNER TYPE

One of two supported tuner can be selected from this item. System must be restarted for this change to take effect.

TELETEXT

NO TEXT: Teletext is totally disabled. TXT/MIX button will not be functional. AUTO picture format mode will be disabled in RF, F-AV and SHVS modes. Naming and sorting functionality during Auto programming will be disabled.

FAST: TOPtext functionality will be disabled.

FAST&TOP: TOPtext functionality is enabled.

TIMER MODE

If OFF TIMER is selected, the user will be able to enter time of the day info for the TV to switch off. If SLEEP TIMER is selected, the user can specify some time period, after which the TV will go to stand by automatically.

MSP CLIP
This selection identifies which method will be used by the sound processor to prevent clipping effects on volume.
AUTO-PROGRAMMING
When the user selects the Auto program item in Setup menu, Country Selection menu is opened. The user must select a country before the Auto programming starts. Broadcast system will be selected according to the country selected.
Broadcast systems according to countries:
BELGIUM BG + L
CROATIA BG
CZECH REP. DK
DENMARK BG
FINLAND BG
FRANCE L + BG
GERMANY BG
GREECE BG
HUNGARY DK
IRELAND I
ITALY BG
NETHERLANDS BG
NORWAY BG
POLAND DK
PORTUGAL BG
SPAIN BG
SWEDEN BG
SWITZERLAND BG + L
TURKEY BG
UNITED KINGDOM I
For countries France, Belgium and Switzerland, auto programming is done twice. For Belgium and Switzerland, first BG channels will be searched, after the search in BG is done, searching will restart for L standard. If the selected country is France, the sequence of standards is reversed, thus, first L then BG.
TELETEXT LANGUAGES
L5C SW decides which teletext language group will be used for teletext decoding, according to the country selected for auto programming.Teletext languages according to countries:
EAST EUROPE:CROATIA ,CZECH_REP, POLAND
WEST EUROPE: BELGIUM ,DENMARK, FINLAND, UK, FRANCE, GERMANY,
IRELAND ,ITALY ,NETHERLANDS, NORWAY, PORTUGAL,SPAIN, SWEDEN, SWITZERLAND, HUNGARY
TURKISH-GREEK:GREECE TURKEY
PC MODE
PC mode can be entered by pressing PC button on the remote controller. User can return back to TV mode by pressing the PC or TV buttons.
After the switching to PC mode, VGA input will be displayed on screen, as soon as the mode (input resolution and frequency) is determined.
If there is no input from the VGA input, NO SIGNAL dialog will be displayed for 15 seconds. At the end of this period if there is no signal from VGA input, the TV will go to Sleep State. While in the sleep state, the TV will keep monitoring the VGA input. If VGA signal is detected, the TV will wake from Sleep State, to PC mode. Alternatively, the user may select to switch the TV on from Sleep State, just like switching on from Stand-by. In this case, the set will switch on from TV mode.

Toshiba DL3970A(F) LCD TV – SMPS schematic

ICs Used: TEA1733, OZ9967